Why Don't Car Engines Melt, But Machine Gun Barrels Do?

Table of Contents (click to expand)

A car engine burns fuel far hotter than steel can melt, yet it shrugs that heat off for 200,000 miles, while a machine gun barrel wrecks itself at a much lower temperature in just minutes. The difference is not how hot each one burns. The engine runs a constant stream of liquid coolant that drains its heat away almost as fast as it is made, while a bare barrel has no such loop and can only leak heat slowly into still air, so the heat builds up until the steel softens and cartridges start firing on their own.

Picture a family sedan on a long summer drive. Inside each cylinder, fuel and air are being set on fire thousands of times a minute. This goes on for hours. The engine does not care. That same engine will do it again tomorrow, and for another 200,000 miles.

Now picture a machine gun. It fires far fewer explosions per minute than the engine does. Yet after a couple of minutes of steady shooting, the barrel is glowing, drooping, and about to wreck itself.

The obvious guess is that the gun must simply burn hotter. It sounds right. It is also wrong, and the reason why is the whole point of this article.

What Is Heat, And Why Is Temperature Really A Race?

Start with the thing everyone gets slightly backwards: heat and temperature are not the same idea.

Heat is energy on the move. It always flows from something hot to something cooler, never the other way. Temperature is just how hot a thing is right now, and it is not fixed. It settles at whatever level balances two competing flows.

Here is the picture to hold on to for the rest of the article. Imagine a kitchen sink with the tap running and the drain open. The tap pours water in. The drain lets water out. The water level is the temperature.

If the tap and the drain move water at the same rate, the level holds steady. Open the tap wider and the level climbs until the deeper water pushes down the drain fast enough to keep up. Now shrink the drain to a pinhole. Same tap, but the water rises and rises, because it cannot escape fast enough.

Temperature is a race between heat coming in and heat draining out. Two machines can take in the same heat and end up hundreds of degrees apart, because one has a wide drain and the other has a pinhole. How much heat you make barely matters. What matters is how fast you drain it.

Temperature is not set by how big the fire is. It is a balance between heat pouring in and heat draining out. Same tap, different drain, wildly different result.
Temperature is not set by how big the fire is. It is a balance between heat pouring in and heat draining out. Same tap, different drain, wildly different result.

Does A Machine Gun Really Burn Hotter Than A Car Engine?

No, and the numbers turn the intuition inside out.

Inside a car engine cylinder, the burning fuel briefly reaches about 2,700 °C (4,900 °F). That is hotter than steel melts. Iron gives way at around 1,500 °C, and the steels used for engine parts soften well below that. So a car engine routinely makes a fire hot enough to destroy the metal holding it, and the metal is fine.

Now the gun. Its fire is not the cooler one. Burning propellant in a barrel runs at roughly 2,200 to 3,200 °C, squarely in the engine's range. What differs is what the metal reaches. During sustained fire, the inside of a machine gun barrel climbs to around 600 to 700 °C (1,100 to 1,300 °F), and that is already enough to ruin it. The two numbers that differ are the ones for the metal.

So both machines make a fire far hotter than steel can survive, and only one keeps its metal out of trouble. The heat made does not decide the outcome. The drain does.

Both machines make a fire far hotter than steel melts. The engine's metal (blue) still sits at coolant temperature, while the gun barrel's own metal reaches 600 to 700 °C, and that is enough to ruin it. The size of the fire is not the problem.
Both machines make a fire far hotter than steel melts. The engine's metal (blue) still sits at coolant temperature, while the gun barrel's own metal reaches 600 to 700 °C, and that is enough to ruin it. The size of the fire is not the problem.

How Does A Car Engine Drain Its Heat?

Only a fraction of the fuel's energy ever reaches the wheels. A rough rule of thumb splits it three ways: a third to useful work, a third out the exhaust, and a third into the engine's own metal. The exact split shifts with how hard you push the engine, but that last third is enormous. Left alone, it would cook the engine in minutes, exactly the way it cooks a gun barrel.

So the engine builds a drain. A big one. Cast into the solid metal, wrapped around each cylinder, are hollow passages called the water jacket. They carry liquid coolant within millimeters of the fire, and a pump forces that coolant to circulate constantly. That word, forces, is the whole game: the engine does not wait for heat to drift away on its own, it pushes a river of fluid past the hot metal to carry it off.

Where does the heat go next? To the radiator, a grid of thin metal fins with a huge surface area, sitting in the airflow at the front of the car. The hot coolant flows through it and hands its heat to the passing air, and a fan pulls more air through when the car is slow or stopped. It is the same trick that gives cooling towers their giant flared shape: more surface, more air, faster draining.

A thermostat governs the whole thing. It is a valve that opens and closes the path to the radiator to hold the engine at a steady temperature. The result is startling. The fire inside hits 2,700 °C, yet the coolant carrying that heat away sits at only about 80 °C (175 °F), and the metal is held far below where it would soften. (The fluid matters too, which is why cars run a coolant mix rather than plain water.) The engine is not surviving the heat. It is draining it, as fast as it arrives.

The coolant loop gets the glory, but the motor oil is a second drain. As it circulates, it carries heat out of the hottest, most cramped corners the water jacket cannot reach, like the underside of the pistons and the bearings.

The closed loop a gun barrel does not have. A pump drives coolant through the engine's water jacket, out to the radiator to drain the heat, and back again, while a thermostat holds the whole thing at a steady temperature.
The closed loop a gun barrel does not have. A pump drives coolant through the engine's water jacket, out to the radiator to drain the heat, and back again, while a thermostat holds the whole thing at a steady temperature.

Now The Gun: All Of The Heat, None Of The Loop

Look at a bare barrel and count its drains. There are none.

No jacket. No pump. No coolant. No radiator. A gun barrel has exactly two ways to lose heat, and both are feeble. First, it soaks heat into its own metal, which buys a little time and no more. Second, it leaks heat off its outer surface into the surrounding air. That slow drift of warmth into still air is the weakest way to move heat there is; the metal cannot hand it over fast enough.

There is a refill between shots, but it is the wrong kind. An engine's intake stroke pulls in a fresh gulp of cool air and fuel that scrubs some leftover heat out of the chamber before the next burn. A gun's chamber gets a fresh cartridge instead. It is being reloaded, not cooled.

So the sink fills up. Heat pours in from every shot and the pinhole drain cannot keep pace. The barrel climbs past the temperature it was built to work at, keeps going, and heads for the 600 to 700 °C where the steel softens. Same physics as the engine, opposite result, entirely because the drain is a pinhole instead of a river.

An M240B machine gun firing at night. The barrel has no jacket, no pump, no radiator. Its only exits for heat are its own metal and the still air around it, and both are slow. (Photo Credit: Sgt. Sarah Fiocco / U.S. Marine Corps, public domain)
An M240B machine gun firing at night. The barrel has no jacket, no pump, no radiator. Its only exits for heat are its own metal and the still air around it, and both are slow. (Photo Credit: Sgt. Sarah Fiocco / U.S. Marine Corps, public domain)

Can A Gun Barrel Actually Melt? (Not Quite)

Here is a small myth to retire: barrels almost never actually melt. Gun steel's melting point is high, and a barrel destroys itself long before it gets there. "Melting" is the folk name for a cluster of heat failures that arrive earlier.

The first is softening. Steel does not have to melt to fail. By 700 °C, gun-barrel steel keeps only about one-eighth of the strength it has at room temperature. Long before melting, the hot bore softens and the high-pressure gas scours it away, wearing out the spiral grooves that spin the bullet for accuracy. A worn bore means a barrel that can no longer shoot straight.

The second failure is the dramatic one: cook-off. Get the chamber hot enough and a loaded cartridge fires on its own, with no trigger pull, because the heat alone lights the propellant. The temperature needed is startlingly low, about 150 °C (300 °F) in one measurement, barely above the boiling point of water. An engine has its own version of this, the knock that engine designers work hard to prevent. Knock and cook-off are cousins: in both, heat sets off a fire at the wrong moment.

How Did Engineers Solve It? By Building The Missing Loop

Everything so far has been one argument: give heat a fast way out and the metal lives. So the fix for an overheating barrel is obvious. Build it a drain. Engineers did, twice.

The first fix barely counts as cooling. If you cannot pull the heat out of the barrel fast enough, pull out the barrel. Modern general-purpose machine guns use quick-change barrels: the crew swaps the hot barrel for a cold spare in seconds and lets the hot one cool on its own time. It is not subtle, but it works. At the rapid rate of fire, an M240 crew is told to change the barrel every two minutes.

The second fix is the one that proves the whole thesis. Around a century ago, engineers looked at a gun barrel and gave it the engine's cooling loop. The classic water-cooled machine guns of the Maxim and Vickers lineage wrapped the barrel in a fat metal jacket and filled it with a few liters of water. As the barrel heated, the water carried the heat off and boiled away as steam. A hose could pipe that steam to a can, condense it, and pour it back in to be reused. A closed cooling loop, bolted onto a gun. The payoff: a Vickers could sustain something like 10,000 rounds an hour, all day, without wrecking itself. Give a gun a liquid cooling loop, and it stops melting.

A Vickers machine gun. The fat cylinder wrapped around the barrel is a water jacket: an engine-style cooling loop bolted onto a gun. It let the gun fire all day without cooking itself. (Photo Credit: York Museums Trust / Wikimedia Commons, CC BY-SA 4.0)
A Vickers machine gun. The fat cylinder wrapped around the barrel is a water jacket: an engine-style cooling loop bolted onto a gun. It let the gun fire all day without cooking itself. (Photo Credit: York Museums Trust / Wikimedia Commons, CC BY-SA 4.0)

Once you see the sink, you see it everywhere. Take the most violent fire humans build on purpose: a rocket engine. The Space Shuttle's main engines ran a combustion chamber hotter than the boiling point of iron. The chamber should vaporize instantly. Those engines survive the same way the car does: before the fuel is burned, it is pumped through channels in the chamber walls to soak up their heat, cooling the metal on its way to the fire. It is the coolant jacket again, with the fuel doing double duty. Build the loop, beat the heat.

A Rocketdyne F-1 engine, five of which lifted the Saturn V. The maze of tubes is not just plumbing. Fuel runs through channels in the chamber walls to cool them before it is burned. It is the engine's coolant jacket, on a rocket. (Photo Credit: NASA, public domain, via Wikimedia Commons)
A Rocketdyne F-1 engine, five of which lifted the Saturn V. The maze of tubes is not just plumbing. Fuel runs through channels in the chamber walls to cool them before it is burned. It is the engine's coolant jacket, on a rocket. (Photo Credit: NASA, public domain, via Wikimedia Commons)
References (click to expand)
  1. Zhang, L.K. et al. (2023). “A Review on Life Prediction Methods of Gun Barrel.” Journal of Physics: Conference Series, 2460, 012042.
  2. Zhao, X. et al. (2020). Gun barrel bore surface temperatures during firing. Materials, 13(24), 5753.
  3. Temperature Estimation in the Combustion Chamber of an Internal Combustion Engine (Safakish, 2012). Journal of Combustion.
  4. Iron: melting point (materials glossary, citing Callister). Princeton University, MAE 324.
  5. Investigating T Finned Barrels for Machine Guns (Chaturvedi, 2019). Advances in Military Technology.
  6. Internal Combustion Engines: energy balance of work, exhaust and coolant. Colorado State University.
  7. Why does an engine cooling system have a thermostat, and how does it relate to coolant? Caltech.
  8. Internal Combustion Engines: coolant operating temperature. Colorado State University.
  9. Heat transfer in a 155 mm compound gun barrel (natural air cooling ineffective; ~12 h cooldown for large-caliber tubes). Applied Thermal Engineering (Wu et al., 2008).
  10. Understanding and Predicting Gun Barrel Erosion (thermal softening; steel strength vs. temperature). DSTO-TR-1757 (Johnston, 2005).
  11. Experimental investigation of a cook-off temperature in a hot barrel (Hameed et al., 2014). Defence Technology.
  12. M240 Machine Gun operator's manual (barrel-change intervals). US Army TM 9-1005-313-10.
  13. Water Cooling and Condensing Equipment (7.5-pint jacket, steam recycling). The Vickers Machine Gun Collection and Research Association.
  14. Vickers Machine Gun (~10,000 rounds/hour sustained). Norfolk Tank Museum.
  15. Space Shuttle Propulsion Trivia (combustion chamber 6,000 °F). NASA Marshall Space Flight Center.
  16. Independent Review of the Failure Modes of F-1 Engine (regenerative fuel cooling). NASA NTRS.